助手标题
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
共[98]条 当前为第1条到20条
 

相关语句
铜板
    A discussion about the performance of the Standard piece of T_2 copper plate
    关于T_2铜板标准件性能问题讨论
    Reasons for Thermal Crack in Mold Copper Plate And the Countermeasures
    结晶器铜板热裂纹原因及对策
    Research upon mold copper plate temperature field in slab continuous casting at high withdrawal speed
    高拉速条件下板坯连铸结晶器铜板温度场研究
    Design of Control System for Automatic Constant-volume Casting of Anode Copper Plate
    阳极铜板自动定量浇铸控制系统的设计
    The phenomenon of spallation in a copper plate due to explosive loading
    炸药爆炸驱动下铜板的层裂现象
    Features and application on Ni-Co alloy coating of copper plate for thin slab mould
    薄板坯结晶器铜板组箱式电镀Ni-Co合金镀层特点及应用
    Numerical Simulation of Temperature Field of Mould Copper Plate for Slab Continuous Casting
    板坯连铸结晶器铜板温度场的数值仿真
    Distribution of Temperature and Heat Flux Density of Thin Slab Continuous Casting Mould Copper Plate
    薄板坯连铸结晶器铜板温度及热流密度分布
    Research on copper plate taper of slab mold
    板坯结晶器铜板锥度的研究
    Finite Element Simulation of Temperature Field of Mold Copper Plate for Slab Continuous Casting
    板坯连铸结晶器铜板温度场有限元仿真研究
    Numerical Simulation of Temperature and Stress Field of Mould Copper Plate for Slab Continuous Casting
    板坯连铸结晶器铜板温度场和应力场的数值仿真
    HIGH POWER UV LASER MICRO-CUTTING OF THIN COPPER PLATE
    薄铜板的高功率紫外激光微切割
    This paper discusses the performance of the Standard piece of T_2 copper plate.
    本文讨论了T_2铜板标准件的性能问题。
    Having taken some related measures, the repair rate of copper plate due to thermal crack has been reduced from 60% down to 8% and under
    在采取相应的若干措施后,铜板因异常热裂纹而返修的比例从原来的60%下降到8%以下。
    A FEM analysis model on the coupling process of the liquid steel of slab between the temperature field and the stress field in the mould has been established on the basis of size and structure of the copper plate tanks and their arrangement in the mould.
    在考虑结晶器铜板水槽结构尺寸和分布的基础上 ,建立了连铸板坯在结晶器内温度场和应力场之间耦合过程的有限元分析模型。
    Results for welding showed that defect free weld were produced on6mm thick copper plate at optimum joining conditions.
    实验结果表明,用搅拌摩擦焊方法焊接6mm厚的T2紫铜板,当焊接规范合适时,可得到成形美观、内部无缺陷、几乎不变形的平板对接接头;
    use of Cu-Cr-Zr alloy as the mould copper plate;
    结晶器铜板本体材质改为Cu-Cr-Zr;
    A kind of Cu-15.5Sn-5P-4.5Ni-0.4Mn brazing filler metal powder produced by gas atomization was used to weld T1 copper plate at 685 ℃ for 20 min,in which the joint length is 6mm and brazing gap thickness is 0.3 mm. The brazing filler melting point,microstructure and mechanical properties of joining were research.
    采用气雾化方法制备了Cu-15.5Sn-5P-4.5Ni-0.4Mn粉末微晶钎料,在685℃/20min条件下炉中真空钎焊T1紫铜板,搭接长度6mm,钎缝宽度0.3mm,研究了钎料熔点、钎焊接头微观组织和力学性能。
    Methods Burger's phantom (Kyoto Scientific Corporation), 20 mm aluminium plate (RPM X-QA, Beijing Institute of Radiation Medicine), 0.5 mm copper plate, RTI Solidose 400 digital dosimeter, PMX-IR kV-time meter, and CPI high-frequency generator were applied to compare the low density signal detection between CR and DR systems for the same X-ray machine, absorber and exposed dose.
    方法采用Burger’s模板、20mm铝板、0·5mm铜板、RTISolidose400数字剂量计、PMX-IR千伏时间计及CPI高频高压发生器,在同一X线机,相同吸收体,相同曝光条件(剂量)下,比较CR、DR的低密度信号检出能力。
    INTERMEDIATE JACKET WITH DOUBLE SPIRAL AND COPPER PLATE HEAD FOR BLAST FURNACE TUYERE
    高炉双螺旋铜板帽风口中套
 

首页上一页12345下一页尾页 

 
CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社