助手标题  
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
   铁齿轮 的翻译结果: 查询用时:0.192秒
图标索引 在分类学科中查询
所有学科
更多类别查询

图标索引 历史查询
 

铁齿轮
相关语句
  adi gear
     Research on Heat Treatment Technique of ADI Gear
     奥贝球铁齿轮热处理工艺的研究
短句来源
     The results show that the properties of ADI are superior to 40Cr quenched steel and that by subsitituting ADI gear for 40Cr quenched steel gear the noise from the diesel engine could be reduced by 1.92 dB(A),and that the noise produced from the side of the gear could be reduced by 5.3 dB(A).
     试验结果表明 ,奥贝球铁齿轮与 4 0 Cr调质钢齿轮相比 ,机械性能高于 4 0 Cr调质钢材料 ,柴油机整机噪声降低了 1.92 d B,齿轮侧噪声下降了 5 .3d B。
短句来源
     After pre wearing for 45 hours,ADI gear has no abnormal wear after running 1 000 hours under the standard working condition,and that the space between the gears is below 0.13 mm to limits. Therefore the ADI gear possesses the better wear resistance and it can meet the requirements for the design and application.
     奥贝球铁齿轮经过 4 5 h磨合后 ,在标定工况下连续运转 10 0 0 h,齿轮无异常磨损 ,齿轮间隙离极限间隙还有0 .13mm的余量 ,所以其摩擦磨损性能合格 ,所生产的奥贝球铁齿轮满足设计使用要求
短句来源
  “铁齿轮”译为未确定词的双语例句
     c) By shot blast strengthening,the ultimate bending fatigue load of ADI gears could be increased by31.7%~47.6%.
     ⑶喷丸强化能使奥贝球铁齿轮极限弯曲疲劳载荷提高31.7%~47.6%。
短句来源
     Analysis of Factors Influencing Property Stability of ADI Gears and Measures to be Taken
     奥贝球铁齿轮性能稳定性的影响因素分析
短句来源
     Experimental results showed that the mechanical properties of ADI gears were higher than that of 40Cr hardened and tempered steel gears. The ADI gears lowered the working noise of the whole diesel engine by 1.92 dB(A) and the noise on the side of the gears by 5.3 dB(A).
     试验结果表明,奥贝球铁齿轮机械性能高于40Cr调质钢,柴油机整机噪声降低1.92dB(A),齿轮侧噪声下降5.3dB(A)。
短句来源
     The result showed that the mechanical properties of ADI gears were higher than that of 40Cr hardened and tempered steel gears.
     试验结果表明,奥贝球铁齿轮与40Cr调质钢齿轮相比,机械性能高于40Cr调质钢材料,柴油机整机噪声降低1.92dB,齿轮侧噪声下降5.3dB。
短句来源
     By using dried clay sand mould,dried clay sand cores and multi-pen shaped top gating system,the large gear wheel with dimension ofφ1400mm×650mm(height )and weight of1600kg was successfully produced without feeder.
     采用干砂型、干砂芯、外冷铁和雨淋式顶注浇注系统,在不用冒口的情况下成功地铸造出φ1400mm×650mm,质量1600kg的大型球铁齿轮
短句来源
更多       
  相似匹配句对
     Austenitic-Bainitic Ductile Iron Gear
     奥氏体——贝氏体球齿轮
短句来源
     Application of Bainite Ductile Iron in Tractor Gears
     贝氏体球在拖拉机齿轮上的应用
短句来源
     Nitriding on Gear
     齿轮渗氮
短句来源
     PARABOLIC GEARS
     抛物线齿轮
短句来源
     Fe.Mo-Cofactor
     钼辅因子
短句来源
查询“铁齿轮”译词为用户自定义的双语例句

    我想查看译文中含有:的双语例句
例句
没有找到相关例句


Using Mg-Ti-Ca-Re-Si-Fe single alloy as a modifying agent, the experimental work for producing compacted graphite cast iron gears with cupola melting iron is described. Produced gears have reached the mechanical properties required by the designer. They need not be heat-treated, have good machinability and very low reject rate.

本文叙述了用Mg—Ti—Ca—Re—Si—Fe单一合金作蠕化剂,用冲天炉铁水制造纺织机齿轮的试验研究工作。试验结果表明,蠕铁齿轮达到了设计者对机械性能的要求,不要热处理,切削加工性能好,废品率低。

In order to ensure that a certain degree of transmission accuracy, the remains deformation of gear teeth must be restricted within a certain range. In other words, the allowable remains deformation depends on the accuracy of the transmission and the conditions under which the gear is working. Based on a large number of test results, the relationship between remains deformation and static bending strengthlimit Films was obtained as follows: Where σ1 -the gear bending stress at the moment when 1 um remains deformation...

In order to ensure that a certain degree of transmission accuracy, the remains deformation of gear teeth must be restricted within a certain range. In other words, the allowable remains deformation depends on the accuracy of the transmission and the conditions under which the gear is working. Based on a large number of test results, the relationship between remains deformation and static bending strengthlimit Films was obtained as follows: Where σ1 -the gear bending stress at the moment when 1 um remains deformation is produced for unit module. K - a coefficient which is dependent on the material and its heat treatment method, σ1 and K for spheroidal cast iron gears are shoun in this paper.

为了保证齿轮达到一定程度的传动精度,必须限制轮齿的残余变形量,即轮齿允许的残余交形量取决于传动精度和齿轮的使用条件。通过一系列试验,发现轮齿齿根的静弯曲极限应力值σ_(F11ms)与齿轮残余变形量δ和模数m两者之间的比值(δ/m)有这样的关系:σ_(F11ms)=σ_1(δ/m)~k。其中σ_1是每单位模数产生1μm残余变形量时的齿根应力,σ_1值取决于材料的机械性能。K为指数,其值取决于材料的种类和热处理工艺。本文给出球铁齿轮的σ_1和K值。

This article sums up the testing results of bending fatigue strength of three kinds of Baintic ductile iron gears. The testing method is an accelerated test for determining the fatigue strength of gears. For calculating the bending fatigue stress 《ISO/TC60 424E Calculation of tooth strength of spur and helical gears》 is adopted.When the number of basic cycles is No = 3×106, the bending fatigue limit stresses σFlim(R = 0. 99) are shown as follows:material σFlim (N/mm2)V-Ti Baintic Ductile Iron 305.7Cu-Mo Austenitic-Baintic...

This article sums up the testing results of bending fatigue strength of three kinds of Baintic ductile iron gears. The testing method is an accelerated test for determining the fatigue strength of gears. For calculating the bending fatigue stress 《ISO/TC60 424E Calculation of tooth strength of spur and helical gears》 is adopted.When the number of basic cycles is No = 3×106, the bending fatigue limit stresses σFlim(R = 0. 99) are shown as follows:material σFlim (N/mm2)V-Ti Baintic Ductile Iron 305.7Cu-Mo Austenitic-Baintic Ductile Iron 242.32Cu-Mo Martensit ic-Baintic Ductile Iron 240.65The measurements and surfaces where failure occurred are analyzed.

本文总结了三种贝氏体球铁齿轮的齿根弯曲疲劳极限应力σ_(F11n)的测定结果。根据齿轮疲劳强度的快速测定方法,采用ISO/TC60424《直齿及斜齿园柱齿轮传动承载能力计算的基本原理》,求得循环基数No=3×10~6时的σ_(F11n)(可靠度为99%)分别为: 作者对测定结果和断口特点进行了初步分析。

 
<< 更多相关文摘    
图标索引 相关查询

 


 
CNKI小工具
在英文学术搜索中查有关铁齿轮的内容
在知识搜索中查有关铁齿轮的内容
在数字搜索中查有关铁齿轮的内容
在概念知识元中查有关铁齿轮的内容
在学术趋势中查有关铁齿轮的内容
 
 

CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社