助手标题  
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
   braze welding 的翻译结果: 查询用时:0.007秒
图标索引 在分类学科中查询
所有学科
金属学及金属工艺
无线电电子学
汽车工业
物理学
自动化技术
航空航天科学与工程
工业通用技术及设备
环境科学与资源利用
更多类别查询

图标索引 历史查询
 

braze welding
相关语句
  钎焊
     Combination Process of Al_2O_3 Ceramic/Steel Using Braze Welding Method in Air
     复相A1_2O_3基陶瓷/钢在大气中直接钎焊的连接工艺
短句来源
     Brazing filler metals of Ag-Cu-In-Sn series, whose melting temperature is between 557~693℃, fit for the braze welding of electron tube, semiconductor and microelectronic device under the condition of vacuum or protective atmosphere.
     Ag-Cu-In-Sn系合金钎料,熔化温度在557~693℃之间,适合于电真空、半导体及微电子器件在真空或保护气氛中无钎剂中温钎焊
短句来源
     Ceramic- metal tappet combined by braze welding was tested in automobile engine. After 1160 hours running, the wear of the ceramic insert itself is 0. 25μp, while that of the quenched 45 steel counterface is 3. 14μm.
     钎焊接合的陶瓷-金属复合挺柱,装在汽车发动机上,工作1160h后,陶瓷镶块自身磨损量约为0.25μp,其对偶件45号淬火钢凸轮的磨损量为3.14μp。
短句来源
     Development and Application of Braze Welding and Ti-Based Braze Materials
     钎焊及钛基钎焊料的发展及应用
短句来源
     The gas leakage failure of braze welding between the phosphorus deoxidized copper tube and stock tank of low carbon steel was investigated by means of metallography,SEM and EDAX analysis.
     针对磷脱氧铜管与低碳钢储罐钎焊后漏气失效问题,采用金相、扫描电镜(SEM)和能谱分析(EDAX)对失效器件进行分析,发现铜管漏气的主要原因是由于钎焊过程中,预热和钎焊工艺不恰当,导致焊接气氛交替出现氧化性和还原性,使得铜管发生氢脆,产生裂纹。
短句来源
更多       
  钎接焊
     Research of hydrogen shield diffusion braze welding technology for precise parts
     精密零件氢气保护扩散钎接焊工艺研究
短句来源
     This paper describes hydrogen shield diffusion braze welding technology for precise parts of copper and compound metal.
     本文阐述的是,铜及其合金精密零件氢气保护扩散钎接焊工艺问题。
短句来源
     The method and technology of oxyacetylene flame braze welding for main cable wrapping at Shantou Bay Bridge were introduced,and the difficulties of the welding were analyzed.
     介绍汕头海湾大桥主缆缠丝所采用的氧- 乙炔火焰钎接焊方法及其工艺,并对主缆缠丝焊接的难点进行了分析。
短句来源
  “braze welding”译为未确定词的双语例句
     Study on Braze Welding Process, Structure and Property of Al 2O 3/Nb with Ni Ti Solder
     Al_2O_3/Ni-Ti钎料/Nb的封接及其组织和性能的研究
短句来源
     Automatic Control for Intermediate Frequency Braze Welding the Stator Coil Water Connectors of 600 MW Turbogenerator
     600MW汽轮发电机定子线圈水接头中频焊接的自动控制
短句来源
     Interface Reaction and Metallographic Observation of a Ti-30Ni Braze Welding Seam
     Ti-30Ni钎缝的界面反应及金相观察
短句来源
     According to the demands of high performance and reliability of vacuum braze welding,the traditional hand-controlled is replaced by PLC automatic control program,so the relevant equipment and operational parameters and technological process are organically coordinated.
     基于真空钎焊性能和高可靠性等的要求,利用PLC自动控制程序取代传统的手动控制,使有关设备和工作参数及工艺流程能有机的协调;
短句来源
     At the same time, the recently developed braze welding device with automatic temperature control for 600 MW turbogenerator is presented.
     同时介绍了新近研制成功的一套600MW汽轮发电机定子线圈水接头自动控温焊接设备.
短句来源
更多       
查询“braze welding”译词为用户自定义的双语例句

    我想查看译文中含有:的双语例句
例句
为了更好的帮助您理解掌握查询词或其译词在地道英语中的实际用法,我们为您准备了出自英文原文的大量英语例句,供您参考。
  braze welding
Join Mild Steel plate by fusion welding and braze welding of four basic joints within parameters of weld integrity and appearance.
      
Gas tungsten arc braze welding with its attendant lower temperatures, can be carried out with less joint preparation.
      


The toughness of the frame and front fork of bicycle has been tested by precooling quenching after the salt bath and braze welding. The result shows that the welding seam to the frame and front fork is tight and smooth when the precooling temperature reaches 880℃ before quenching. The martensite structure of hardening position also is compact. The impact and fatigue life of the frame and front fork will be prolonged.

本文研究了自行车架和前叉盐浴钎焊后预冷淬火强火。结果表明,预冷至880℃淬火,焊缝饱满、严密,强化部位低碳马氏体组织细致良好,车架、前叉的冲击疲劳寿命显著提高。

A Failure of a balltooth bit mainly is a breaking of peripheral tooth due to inproper tooth fixing technique and parameters to be used. Base on great practices and experiments of rock drilling, this paper has detailly analyzed suitable conditions and parameter selecteons of hot inserted, cold press and braze welding tooth fixing techniques. From the analyses of tooth firmly fixed, anti-radial abrasion, providing tooth regrinding, reducing machining cost, increasing labour and production efficiency, simple...

A Failure of a balltooth bit mainly is a breaking of peripheral tooth due to inproper tooth fixing technique and parameters to be used. Base on great practices and experiments of rock drilling, this paper has detailly analyzed suitable conditions and parameter selecteons of hot inserted, cold press and braze welding tooth fixing techniques. From the analyses of tooth firmly fixed, anti-radial abrasion, providing tooth regrinding, reducing machining cost, increasing labour and production efficiency, simple technique and others, the braze welding tooth fixing technique has more advantages than others. Therefor, an induction braze welding tooth fixing is best for the ball tooth bit with a small diameter. A press fixing is best for the ball tooth bit with a large diameter.

通过球齿钻头的冷压、热嵌和钎焊固齿工艺、技术参数的分析研究,指出钎焊较有前途.

This paper describes hydrogen shield diffusion braze welding technology for precise parts of copper and compound metal. This is a novel advanced technology between transition liquid phase (TLP) diffusion welding and brazing, and it has both advantages. Diffusion elements, selecting of common crystal phase system,screening and diffusion-analysis of common crystal reaction process, are introduced emphatically in the paper. This paper simply deseribes junction structure, performance and welding...

This paper describes hydrogen shield diffusion braze welding technology for precise parts of copper and compound metal. This is a novel advanced technology between transition liquid phase (TLP) diffusion welding and brazing, and it has both advantages. Diffusion elements, selecting of common crystal phase system,screening and diffusion-analysis of common crystal reaction process, are introduced emphatically in the paper. This paper simply deseribes junction structure, performance and welding quality, as well as application state of this technology.

本文阐述的是,铜及其合金精密零件氢气保护扩散钎接焊工艺问题。这是一种界于TLP扩散焊和钎焊工艺之间的一种新型先进工艺,兼有两者之长。文中对扩散元素,共晶相系的选取、筛选和扩散——共晶反应过程机理分析作了重点论述,并对其接头组织,性能和焊接质量及本工艺的应用情况作了简要介绍。

 
<< 更多相关文摘    
图标索引 相关查询

 


 
CNKI小工具
在英文学术搜索中查有关braze welding的内容
在知识搜索中查有关braze welding的内容
在数字搜索中查有关braze welding的内容
在概念知识元中查有关braze welding的内容
在学术趋势中查有关braze welding的内容
 
 

CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社