喂料段 feeding zone(4)   feeding zone      Theory and practice of feeding zone in screw press      螺旋榨油机喂料段的理论与实践 短句来源      A model for the conveying of solid polymer in the feeding zone of two rotors continuous mixer was proposed.      对双转子连续混炼机转子喂料段固体物料的输送过程进行了理论分析,提出了描述此过程的物理模型。 短句来源      Furthermore,the feeding zone having an enough covering length of grooved bushing work successfully out transport of the special soft oilseed with high oil content and low crude fiber content without other forced feeding sets.      而且 ,在喂料段通过增大输送螺旋的封料长度 ,设置带阻转槽的衬套成功地解决了这种高油、低粗纤维含量的软油料的输送 ,无需专门的强制喂料装置。 短句来源      The feeding zone with a grooved bushing can work successfully out transport of the special soft oilseed with high oil content and low crude fiber content without other forced feeding sets.      实践证明 ,在榨油机的喂料段附加一个带阻转槽的衬套是实现高油分、低粗纤维含量的软油料在榨油机中顺畅喂料的行之有效的方法。 短句来源   “喂料段”译为未确定词的双语例句      In order to develop the extrusion cooking process conditions of the coarse grain nutrition breakfast cereals, the extrusion expansion temperature, the moisture content, the screw speed and the feeding rate were studied and the optimized parameters were obtained.      从调整膨化温度、物料含水率、螺杆转速、喂料速率等方面对五谷杂粮营养早餐谷物食品的挤压膨化工艺条件进行了探讨，最佳膨化技术参数为：DS56-X型双螺杆挤压机挤压腔内喂料段/挤压段/溶化段的温度分别为70℃、140-160℃和170-180℃； 物料含水率控制在15-17%左右； 短句来源      The axial pressure distribution in the whole process of rubber cold - feed extrusion was analyzed. The axial pressure in the screws was measured and imitated.      对橡胶冷喂料挤出过程轴向压力分布进行了实验研究及理论分析,以实验数据为基础,拟合出了轴向压力分布函数,并分析了喂料段饥饿喂料与喂料返胶的主要成因。 短句来源      The influence of frictional factors on solid conveying ratio(Q)of rubber cold -feed ex-trusion was analyzed by theory and ex periment. The influence of the temperature of feed-section(T b ),screw speed,physical performances of the stocks on Q was discussed. The length of feed -se ction was calculated.      对橡胶冷喂料挤出过程喂料段固体输送率(Q)的影响因素进行了理论分析及实验研究,讨论了喂料段机筒温度(Tb)、螺杆转速(n)和胶料物理性能对摩擦系数(f)及Q的影响,预测了喂料段长度,综合分析了摩擦因素与胶料性能对喂料效率的作用。 短句来源      A trinomial equation for output-pressure decrease was deduced by the simple trilamina model of non-plug solid conveying and stress-velocity equation based on the non-plug solid conveying theory in single-screw extruder.      基于单螺杆挤压机固体输送段的非塞流理论 ,将榨油机的喂料段螺槽中的油料简化为上、中、下 3层 ,通过应力 -速度方程 ,推导出产量与压力降的三次方程。 短句来源      The results show that increasing covered length of the feeding screw and friction coefficient inner the barrel can raise pressure at the feed end and capacity of press.      结果表明 ,适当增加喂料螺旋的覆盖长度和榨笼内壁的摩擦因数是提高喂料段末端压力和输送能力的有效途径。 短句来源   相似匹配句对      Analysis of the Feeding Part of Cold Rubber Feeding Extruder      橡胶冷喂料挤出机加料段浅析 短句来源      Theory and practice of feeding zone in screw press      螺旋榨油机喂料段的理论与实践 短句来源      2. kick-off section;      2，造斜段； 短句来源      3, horizontal section.      3．水平段。 短句来源      Systematic research on the PIM products' tolerance has been made: in this dissertation, such as:1) Control of the feedstock.      1)喂料制备的控制。 短句来源 查询“喂料段”译词为用户自定义的双语例句     我想查看译文中含有：的双语例句 为了更好的帮助您理解掌握查询词或其译词在地道英语中的实际用法，我们为您准备了出自英文原文的大量英语例句，供您参考。   feeding zone It was probably a feeding zone along the oceanic spreading center sitting on top of a mantle diapir. 例句来源       Solid transportation in the feeding zone of intermeshing co-rotating twin-screw extruders 例句来源       A mathematical model was proposed for the characteristics of solid transportation in the feeding zone of an intermeshing co-rotating twin screw extruder. 例句来源       This paper also suggests a solution for the mathematical expressions describing the stress and velocity fields in the solid feeding zone of a twin-screw extruder. 例句来源       The interpretation of the non-uniform enrichment in C, N and S in Saturn requires that ice was less abundant at 10 AU than at 5 AU so that CO and N2 were not clathrated in the feeding zone of the planet while CH4, NH3 and H2S were. 例句来源       更多                    A model for the conveying of solid polymer in the feeding zone of two rotors continuous mixer was proposed. The model enable us to predict the production of continuous mixer. It was concluded that the production of continuous mixer had a direct relation to feeding rate, but was out of relation to rotating speed of totor.             对双转子连续混炼机转子喂料段固体物料的输送过程进行了理论分析,提出了描述此过程的物理模型。运用该物理模型,得出了计算连续混炼机固体输送速率的公式,并由此提出双转子连续混炼机的产量与喂料量成正比以及与转子转速无关的结论。 文摘来源          The axial pressure distribution in the whole process of rubber cold - feed extrusion was analyzed. The axial pressure in the screws was measured and imitated. The reason of hungry - feed and back -feed was analyzed also. The results indicateed that the distribution function of pressure along the axis was almost exponential function, the hardness, viscosity andtensile strength of the stocks not only influenced the axial pressure but also were important factors forming hungry - feed and back - feed. Fluctuati...             对橡胶冷喂料挤出过程轴向压力分布进行了实验研究及理论分析,以实验数据为基础,拟合出了轴向压力分布函数,并分析了喂料段饥饿喂料与喂料返胶的主要成因。结果表明,轴向压力基本是按指数分布的;胶料的邵尔A型硬度、粘度及拉伸强度不但影响螺槽内压力的大小,也是饥饿喂料及喂料返胶的重要因素;轴向压力波动与螺杆的几何结构变化有关。 文摘来源          The influence of frictional factors on solid conveying ratio(Q)of rubber cold -feed ex-trusion was analyzed by theory and ex periment.The influence of the temperature of feed-section(T b ),screw speed,physical performances of the stocks on Q was discussed.The length of feed -se ction was calculated.The effects of friction al factors and the performance of the stocks on feed -efficiency were analyzed synthetically.The results indicated that T b had an effect on friction between rub ber stock andb...             对橡胶冷喂料挤出过程喂料段固体输送率(Q)的影响因素进行了理论分析及实验研究,讨论了喂料段机筒温度(Tb)、螺杆转速(n)和胶料物理性能对摩擦系数(f)及Q的影响,预测了喂料段长度,综合分析了摩擦因素与胶料性能对喂料效率的作用。结果表明:Tb对冷喂料挤出的胶料与筒壁的摩擦系数有一定影响,Tb最佳值为40～50℃。红管胶与垫带胶的邵尔A型硬度较高,容易在喂料口打滑,对Q有影响。拉伸强度较小的红管胶,不易形成喂料返胶,但容易形成饥饿喂料。拉伸强度较大的普通内胎胶及胎面胶,在螺杆喂料段输送能力较低时,能形成喂料返胶。 文摘来源   << 更多相关文摘         相关查询: 段( 段 喂料 段码 基于段 段偏移 段切除术 段或 分离段 段特殊 粉末喂料 细段  对查询结果不满意

CNKI小工具 在Springer中查有关的英文论文 在知识搜索中查有关喂料段的内容 在数字搜索中查有关喂料段的内容 在概念知识元中查有关喂料段的内容 在学术趋势中查有关喂料段 的内容

CNKI主页 |  设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务

2008 CNKI－中国知网

京ICP证040431号 互联网出版许可证 新出网证(京)字008号 北京市公安局海淀分局 备案号：110 1081725  2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社