助手标题  
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
   mould for slab 的翻译结果: 查询用时:0.006秒
图标索引 在分类学科中查询
所有学科
冶金工业
更多类别查询

图标索引 历史查询
 

mould for slab
相关语句
  板坯结晶器
     The influence of casting speed on the average heat flux of mould for slab continuous casting was discussed.
     通过计算 8 0 88块板坯的平均热流研究了拉速对板坯结晶器平均热流的影响。
短句来源
  “mould for slab”译为未确定词的双语例句
     Reasonable structure shape of submerged entry nozzle (SEN) which was suitable to 160 mm × 1050 mm mould for slab continuous casting and casting speed range from 0, 8 to 1. 6 m/min. was researched by the method of water model experiment in the paper.
     报道了采用水力学模拟实验研究适应济钢板坯连铸结晶器断面160 mm×1050 mm、拉速0.8~1.6m/min的合理伸入式水口结构形式。
     Cold State Model and Structure Optimizing of Concaster Mould for Slab at Anyang Iron & Steel
     安钢板坯连铸机结晶器冷态模型和结构优化
短句来源
     NUMERICAL SIMULATION ON FLUID FLOW IN MOULD FOR SLAB CONTINUOUS CASTING
     板坯连铸结晶器内钢液流动数值模拟
短句来源
     Numerical Simulation on Fluid Field in Mould for Slab Concasting
     板坯连铸结晶器钢液流场的数学模拟
短句来源
     STUDY ON WATER MODEL OF SUBMERGED ENTRY NOZZLE IN MOULD FOR SLAB CONTINUOUS CASTER
     板坯连铸结晶器浸入式水口水力学模拟研究
更多       
  相似匹配句对
     Slab Mould
     板坯结晶器
短句来源
     the mould 40℃ ;
     模具温度为40℃;
短句来源
     mould change irregularly.
     霉菌变化趋势没有规律性。
短句来源
     Tools for Mould Making
     用于模具制造的刀具
短句来源
     Design of the Injection Mould for the Connectors
     连接器注射模设计
短句来源
查询“mould for slab”译词为用户自定义的双语例句

    我想查看译文中含有:的双语例句
例句
没有找到相关例句


A software has been developed to simulated and calculated the temperature distribution and steel stream status in the continuous casting mould for slabs and billets using limited differential display. The calculated results agree well with the actual data determined.

本文叙述了所开发的采用有限差分显示法模拟计算方坯、板坯连铸机结晶器内温度分布和钢水流动情况的计算软件。结果表明,计算值和现场测定值基本吻合。

The influence of casting speed on the average heat flux of mould for slab continuous casting was discussed. The results indicated that the casting speed had strong influences on the average heat flux of mould. The average heat flux at broad edges of mould were increased with the casting speed when the casting speed is 0.6~1.2 m/min. If the casting speed exceed 1.2 m/min, the average heat flux at broad edges was changed slowly, but the average heat flux at narrow edges was enhanced with the...

The influence of casting speed on the average heat flux of mould for slab continuous casting was discussed. The results indicated that the casting speed had strong influences on the average heat flux of mould. The average heat flux at broad edges of mould were increased with the casting speed when the casting speed is 0.6~1.2 m/min. If the casting speed exceed 1.2 m/min, the average heat flux at broad edges was changed slowly, but the average heat flux at narrow edges was enhanced with the casting speed. The average heat flux between the broad edges and the narrow edges has 0.2 MW/m 2 difference.

通过计算 8 0 88块板坯的平均热流研究了拉速对板坯结晶器平均热流的影响。结果表明 :拉速对结晶器宽边的平均热流有显著的影响 ,拉速在 0 .6~ 1.2 m / m in范围内 ,结晶器宽边平均热流随拉速提高而增加 ;当拉速超过 1.2 m / m in后 ,结晶器宽边平均热流随拉速增加而提高的幅度变得很小 ;结晶器窄边的平均热流较宽边的热流约低 0 .2 MW/ m2 ,当拉速超过 1.2 m / m in后 ,结晶器窄边的平均热流仍可随拉速的进一步提高而增加

According to the mould for slab concaster at Anyang Iron & Steel, a water model in the ratio of 1 to 1 has been established and the optimum parameters for submerged entry nozzle (SEN) - inclination of SEN 20 degrees, immersing depth 200 mm and casting speed 0.8 m/min are obtained.

以安阳钢铁公司板坯连铸机结晶器为原型 ,采用 1:1的比例建立起一套水模型模拟研究系统 ,正交试验得出浸入式水口的最优化参数 :水口出口倾角 2 0° ,浸入深度 2 0 0mm ,拉速 0 .8m min。

 
<< 更多相关文摘    
图标索引 相关查询

 


 
CNKI小工具
在英文学术搜索中查有关mould for slab的内容
在知识搜索中查有关mould for slab的内容
在数字搜索中查有关mould for slab的内容
在概念知识元中查有关mould for slab的内容
在学术趋势中查有关mould for slab的内容
 
 

CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社