助手标题  
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
   curve of mould 的翻译结果: 查询用时:0.17秒
图标索引 在分类学科中查询
所有学科
金属学及金属工艺
更多类别查询

图标索引 历史查询
 

curve of mould
相关语句
  “curve of mould”译为未确定词的双语例句
     The ray tracing method and proportional spacing method were combined in the proposed method to find the position of distributed data points on the entrance circle. The fast parameterized modeling oriented CAE was realized based on the function partition that affects extrusion flow, where the cubic polynomial was viewed as the curve of mould.
     该方法采用射线法与比例间隔法相结合的方法确定入口圆周上的型值点位置,以三次多项式曲线为模腔曲面型曲线,基于对挤出流动影响的功能划分,实现了面向CAE的参数化的模型快速构建。
短句来源
     The result shows the maximum stress 200mm below the level of the liquid in inside curve,outside curve and side of mould,especially the second maximum below the inside curve of mould merits attention,which provides the scientific basis for optimum mould design. 
     结果表明:内弧、外弧、侧面均在液面下200mm处应力最大,并且值得注意的是结晶器的内弧在下部出现应力的二次峰值。 此研究结果为结晶器的优化设计提供了科学的依据。
短句来源
  相似匹配句对
     Curve and error of mould oscillation
     结晶器振动的运动曲线与误差
短句来源
     curve
     曲线
短句来源
     S's mould curve of China urbanization process is studied
     中国城市化进程的S型曲线研究
短句来源
     Research and Design of the Curve of Electrode Extruder Mould-Mouth
     电极挤压机型咀曲线的研究和设计
短句来源
     Research on tolerance for curve radius of mould copper tube
     结晶器铜管弧形半径的公差研究
短句来源
查询“curve of mould”译词为用户自定义的双语例句

    我想查看译文中含有:的双语例句
例句
没有找到相关例句


The thermal stress in curved mould has been studied by the method of thermallight bullet.The result shows the maximum stress 200mm below the level of the liquid in inside curve,outside curve and side of mould,especially the second maximum below the inside curve of mould merits attention,which provides the scientific basis for optimum mould design.

采用热光弹法对弧形小方坯结晶器的热应力进行了研究。结果表明:内弧、外弧、侧面均在液面下200mm处应力最大,并且值得注意的是结晶器的内弧在下部出现应力的二次峰值。此研究结果为结晶器的优化设计提供了科学的依据。

In this paper, the technological principle on chosing and determining of oscillating waveform curve of mould is discussed. The influences of the waveform curve on process results of mould oscillation and operating condition of oscillation unit are analyzed. The limit form of non-sinusoidal oscillation of mould is put forword, and further optimium aim of non-sinusoidal oscillation form of mould is pointed out.

本文讨论结晶器振动波形曲线选择与确定的技术原则,分析了结晶器振动波形曲线对结晶器振动工艺效果及振动装置使用状况的影响,给出结晶器非正弦振动的极限形式,指出了结晶器非正弦振动形式优化的方向。

The mould temperature field during liquid-solid extrusion was researched by theoretical analysis combining with experimental testing. The curves of mould axial and radial temperature -time were obtained. The change of mould temperatures and its effects on the formation process were analyzed. The simulated results was well in agreement with experimental ones, showing the effectiveness of the model and providing a theoretical basis for optimizing mould design and practical application of...

The mould temperature field during liquid-solid extrusion was researched by theoretical analysis combining with experimental testing. The curves of mould axial and radial temperature -time were obtained. The change of mould temperatures and its effects on the formation process were analyzed. The simulated results was well in agreement with experimental ones, showing the effectiveness of the model and providing a theoretical basis for optimizing mould design and practical application of composites in liquid-solid extruding casting.

采用有限元模拟与试验研究相结合的方法,研究了液固挤压复合材料工艺过程的模具温度场,得到了模具温度沿径向和纵向随时间变化的曲线,分析了模具温度变化规律及其对成形过程的影响。结果表明,在浸渗保压和挤压过程中,挤压筒各处温度变化的总趋势是先升后降,在同一高度下,内侧比外侧温度变化更为剧烈;成形模温度的变化趋势是上部内侧比下部外侧变化要大,挤压后期各部位温度分布逐渐趋于一致。模拟结果与试验结果吻合较好,说明所建模型的有效性,为优化模具设计和液-固挤压复合材料工艺的实际应用提供了理论依据。

 
<< 更多相关文摘    
图标索引 相关查询

 


 
CNKI小工具
在英文学术搜索中查有关curve of mould的内容
在知识搜索中查有关curve of mould的内容
在数字搜索中查有关curve of mould的内容
在概念知识元中查有关curve of mould的内容
在学术趋势中查有关curve of mould的内容
 
 

CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社