助手标题  
全文文献 工具书 数字 学术定义 翻译助手 学术趋势 更多
查询帮助
意见反馈
   非敏化 的翻译结果: 查询用时:0.387秒
图标索引 在分类学科中查询
所有学科
金属学及金属工艺
更多类别查询

图标索引 历史查询
 

非敏化
相关语句
  non-sensitized
     INTERGRANULAR CORROSION AND PHOSPHOR SEGREGATION AT GRAIN BOUNDARY OF NON-SENSITIZED 00Cr25Ni22Mo2N SUPERPURE AUSTENITIC STAINLESS STEEL
     超纯奥氏体不锈钢00Cr25Ni22Mo_2N非敏化态晶间腐蚀与磷(硅)的晶界偏聚
短句来源
     Intergranular Corrosion And Phosphor Segregation at Grain Boundary of Non-sensitized _(00)Cr_(25)Ni_(22)Mo_(2)N Superpure Austenitic Stainless Steel
     超纯奥氏体不锈钢00Cr25Ni22Mo2N非敏化态晶间腐蚀与磷(硅)的晶界偏聚
短句来源
     Relations Between the Non-Sensitized Intergranular Corrosion and the Potentials of Urea Grade 316L Stainless Steel
     尿素级316L不锈钢的非敏化晶间腐蚀与电位的关系
短句来源
     Relations Between the Non-Sensitized Intergranular Corrosion and the Potentials and Test Method of Its Susceptibility for 316L Stainless Steel
     316L不锈钢的非敏化态晶间腐蚀与电位的关系及其敏感性的检测方法
短句来源
     Whereas the impurities like P and Si etc in the steel were the main culprits for the non-sensitized intergranular corrosion.
     而钢中含有P、Si等杂质则是引起非敏化态晶间腐蚀的主要原因。
短句来源
更多       
  “非敏化”译为未确定词的双语例句
     RELATIONS BETWEEN THE NON—SENSITIZED INTERGRANULAR CORROSION AND THE POTENTIALS FOR UREA GRADE 316L STAINLESS STEEL
     尿素级316L不锈钢的非敏化态晶间腐蚀与电位的关系
短句来源
     A SUMMARY OF THE STUDY OF NONSENSITIZED INTERGRANULAR CORROSION OF AUSTENITIC STAINLESS STEEL
     奥氏体不锈钢非敏化态晶间腐蚀研究概况
短句来源
     A New Technique for Detecting the Susceptibility to Intergranular Corrosion of Non-Sensitised Stainless Steels
     检验不锈钢非敏化态晶间腐蚀敏感性的新方法
短句来源
     The authors suggest that the potential difference between the grain and its boundary due to the segregation resulted in the observed intergranular corrosion.
     作者认为,磷的晶界偏聚造成的与晶内在腐蚀电解质溶液中的电位差,是这种超纯奥氏体不锈钢非敏化态晶间腐蚀的原因。
短句来源
     On the basis of theoretical analysis and experimental research,the authordetermined the best alloy system of weld metal(0Cr20Ni10)and the optimumferrite content(3.5—6.5%). At the same time the author also proposed a newsubmerge arc automatic welding process with low heat input and high speed(q≤1600J/mm,v≥34m/h)to cool the welds by spray water in crystallizationand non-susceptible postweld stress relieving heat treatment regulation with twoquick temperature rise rates.
     作者通过理论分析和实验研究,确定了大厚度不锈钢焊缝的最优合金系统(0Cr20Ni10)和最佳铁素体含量(3.5—6.5%),提出了低热输入快速埋弧自动焊方法(q≤1600J/mm,v≥34m/h)和焊缝结晶过程水喷淋冷却措施以及二级快速升温非敏化消除应力热处理制度。
短句来源
更多       
  相似匹配句对
     A SUMMARY OF THE STUDY OF NONSENSITIZED INTERGRANULAR CORROSION OF AUSTENITIC STAINLESS STEEL
     奥氏体不锈钢敏化态晶间腐蚀研究概况
短句来源
     A New Technique for Detecting the Susceptibility to Intergranular Corrosion of Non-Sensitised Stainless Steels
     检验不锈钢敏化态晶间腐蚀敏感性的新方法
短句来源
     Single Transition Sensitization
     单跳变敏化
短句来源
     Non coding mRNA.
     编码的mRNA
短句来源
     Generalized Boolean Negation
     广义布尔
短句来源
查询“非敏化”译词为用户自定义的双语例句

    我想查看译文中含有:的双语例句
例句
为了更好的帮助您理解掌握查询词或其译词在地道英语中的实际用法,我们为您准备了出自英文原文的大量英语例句,供您参考。
  non-sensitized
Samples of serum, liver tissues and small intestine were collected two weeks later, and another group of non-sensitized mice was set as the normal group.
      
Sensitization with TMA had no effect on the lung function before challenge, but TMA-BSA challenge resulted in an early asthmatic response as compared to the non-sensitized rats, irrespective of AM depletion.
      
Dose-response tests revealed that both drugged groups learned to suppress stereotypy in order to feed at 2 mg/kg, but only the non-sensitized group could do so at 4 mg/kg.
      
daily for 21 days and were then separated into sensitized or non-sensitized subgroups on the basis of weekly locomotor activity tests.
      
Smaller increases were seen in the ventrolateral caudate-putamen of sensitized animals (+18% vs control, P>amp;lt;0.02; and 12% vs non-sensitized mice, P>amp;lt;0.07).
      
更多          


Silicon content severly influences the behavior of intercrystalline corrosion of the extra low carbon, Cr-Ni austenite stainless steels in strong oxidizing concentrated nitric acid. In sensitized high purity stainless steel containing Si less than 0.1% the intergranular corrosion susceptibility decreases while in non-sensitized high Si stainless steel containing Si more than 2% the intergranular corrosion susceptibility decreases. The modelling of correlation between Si content and corrosion rate of extra low...

Silicon content severly influences the behavior of intercrystalline corrosion of the extra low carbon, Cr-Ni austenite stainless steels in strong oxidizing concentrated nitric acid. In sensitized high purity stainless steel containing Si less than 0.1% the intergranular corrosion susceptibility decreases while in non-sensitized high Si stainless steel containing Si more than 2% the intergranular corrosion susceptibility decreases. The modelling of correlation between Si content and corrosion rate of extra low carbon, Cr-Ni austenite stainless steels has been identified in 98% smoke nitric acid. Based on the distribution profile of test data, the following exponential model has been selected:Y=B1+B2exp-[B3(X-B4)2]where Y is corrosion rate (g/m2.h); X is Si content in steel (%); B1, B2, B3, B4 is model parameters. These parameters were estimated by simplex searching method.

超低碳铬镍奥氏体不锈钢中的硅含量,对钢在强氧化性介质浓硝酸中晶间腐蚀行为,有着重要的影响,硅含量小于0.1%的高纯不锈钢,可降低敏化态晶间腐蚀,而硅含量大于2%的高硅不锈钢则可以降低非敏化态晶间腐蚀。 本文采用电子计算机对超低碳铬镍奥氏体不锈钢在98%发烟硝酸中腐蚀率和钢中硅含量关系的数学模型,进行了辨识。根据试验数据散点图形状,选定指数模型: Y=B_1+B_2exp〔-B_3(X—B_4)~2〕,其中Y为腐蚀率(g/m~2·h),X为钢中硅含量(%),B_(19) B_(29) B_(39) B_4为模型参数。模型参数采用非线性回归的单纯形搜索法进行估计。

The corrosion behavior and mechanism of 00Cr25Ni22Mo2N superpure austenitic stainless steel in urea processing environment was studied using metallography, SEM, TEM, SIMS and AES techniques. The results show that the gas extraction tube made of non-sensitized 00Cr25Ni-22Mo2N steel suffered intergranular corrosion. Corrosive media penetrated not only into the tube wall through grain boundaries but also expan ded from the boundary towards the inside of the grain. Therefore, funnel shape penetration paths were...

The corrosion behavior and mechanism of 00Cr25Ni22Mo2N superpure austenitic stainless steel in urea processing environment was studied using metallography, SEM, TEM, SIMS and AES techniques. The results show that the gas extraction tube made of non-sensitized 00Cr25Ni-22Mo2N steel suffered intergranular corrosion. Corrosive media penetrated not only into the tube wall through grain boundaries but also expan ded from the boundary towards the inside of the grain. Therefore, funnel shape penetration paths were formed, which were wider but less deep than common intergranular corrosion of sensitized stainless steel. Neither depletion of chromium nor precipitates were found at the grain-boundary. However, phosphor ( and silicon ) was segregated at grain boundaries to a great extent. Semiquantitative calculation indicates that phosphor content at the grain boundary is about 25wt%, three orders of magnitude higher than the content whithin the grain. The authors suggest that the potential difference between the grain and its boundary due to the segregation resulted in the observed intergranular corrosion.

运用金相、电子显微镜观察及表面分析技术,研究了超纯奥氏体不锈钢00Cr25Ni22Mo2N制造的汽提管在尿素生产环境下的腐蚀形态和机理。结果表明:该钢种在生产条件下产生非敏化态晶间腐蚀。其特征是腐蚀介质不仅沿晶界向钢的内部渗入,而且同时向晶界的两侧扩展,因而在管断面上观察到的晶间腐蚀路径较宽,但深度较浅并呈现漏斗形貌。电子显微镜观察、二次离子质谱、俄歇能谱分析及计算表明,这种材料晶界不贫铬、无第二相沉淀,但有磷(硅)的高度偏聚。晶界区磷的含量(约25%)比晶内高约三个数量级。作者认为,磷的晶界偏聚造成的与晶内在腐蚀电解质溶液中的电位差,是这种超纯奥氏体不锈钢非敏化态晶间腐蚀的原因。

On the basis of theoretical analysis and experimental research,the authordetermined the best alloy system of weld metal(0Cr20Ni10)and the optimumferrite content(3.5—6.5%).At the same time the author also proposed a newsubmerge arc automatic welding process with low heat input and high speed(q≤1600J/mm,v≥34m/h)to cool the welds by spray water in crystallizationand non-susceptible postweld stress relieving heat treatment regulation with twoquick temperature rise rates.Then 7 arrangements of quality control are...

On the basis of theoretical analysis and experimental research,the authordetermined the best alloy system of weld metal(0Cr20Ni10)and the optimumferrite content(3.5—6.5%).At the same time the author also proposed a newsubmerge arc automatic welding process with low heat input and high speed(q≤1600J/mm,v≥34m/h)to cool the welds by spray water in crystallizationand non-susceptible postweld stress relieving heat treatment regulation with twoquick temperature rise rates.Then 7 arrangements of quality control are used.and the resultant welding quality is excellent.Welding of products proved thattechnical and economic effects of the new material and technology are remar-kable.

作者通过理论分析和实验研究,确定了大厚度不锈钢焊缝的最优合金系统(0Cr20Ni10)和最佳铁素体含量(3.5—6.5%),提出了低热输入快速埋弧自动焊方法(q≤1600J/mm,v≥34m/h)和焊缝结晶过程水喷淋冷却措施以及二级快速升温非敏化消除应力热处理制度。通过七个环节的质量控制,焊接质量极为优良。新的材料和工艺经产品焊接实践,证明其技术效果和经济效益是显著的。

 
<< 更多相关文摘    
图标索引 相关查询

 


 
CNKI小工具
在英文学术搜索中查有关非敏化的内容
在知识搜索中查有关非敏化的内容
在数字搜索中查有关非敏化的内容
在概念知识元中查有关非敏化的内容
在学术趋势中查有关非敏化的内容
 
 

CNKI主页设CNKI翻译助手为主页 | 收藏CNKI翻译助手 | 广告服务 | 英文学术搜索
版权图标  2008 CNKI-中国知网
京ICP证040431号 互联网出版许可证 新出网证(京)字008号
北京市公安局海淀分局 备案号:110 1081725
版权图标 2008中国知网(cnki) 中国学术期刊(光盘版)电子杂志社