Furthermore,the influences of process conditions on product quality are studied.
The process conditions of preparing anhydrous manganese chloride were studied,which adopt manganese-rich slag as the raw material and use hydrochloric acid as the lixiviant.
Influnce of Process Conditions on the Properties of SrTiO_3 Powder Prepared by Chemical Coprecipitation
Study on process conditions in ceramic membrane microfiltration enhanced procedure
Optimization of Process Conditions on Sedimentation Volume of Ultrafine Calcium Carbonate by Orthogonal Experiment
Test of Technological Conditions of W-Mn/SiO_2 Catalyst for Oxidative Coupling of Methane in a Fluidized-bed Reactor
SEPARATION OF PROPYLENE BY FACILITATED TRANSPORT MEMBRANES (I) TECHNOLOGICAL CONDITIONS
Results showed that the better technological conditions as following: reaction temperature 40℃,constant temperature reaction time 40 min,sedimentation time 120 min,dosage of the surface active reagent 4ml,the proportion of ammonia and magnesium sulfate 6:1.
EXTRACTION OF THE CITRIC ACID FROM THE FERMENTATION LIQUOR BY THE LIQUID MEMBRANE SEPARATION PROCESS AND TECHNOLOGICAL CONDITIONS
Synthetic Porous Silica by Wollastonite ——Study on Technological Conditions and Product Characteristics
Relativity of the Tube Body Corrodesion and the Technological Condition in NSP Kiln
Influence of technological condition on synthesis of β'-Sialon powder from clay by carbothermal reduction-nitridation
-C_(11)A_7·CaF_2·Consequently, the properties of the cements are determined by the mineral combination of the clinkers. The technological condition including sintering temperature and clinker composition, from which each type of mineral combination is formed, have been found.
Ⅳ类组合 C_3S-C_2S-F_(ss)-C_3A-C_4A_3S-C_(11)A_7·CaF_2 在本试验的参数范围内,找出了出现各类矿物组合的 工艺条件。
The technological condition of making Ni-B-Al2O3 combined plating film was studied and re
研究了在Ni-B化学镀液中添加α-Al_2O_3微粒,而得到Ni-B-Al_2O_3复合镀层的 工艺条件; 并对其镀层性能进行了测试。
With P evolving additive EA P used as P source in Zn Fe P plating, effects of bath composition and technological condition on P and Fe contents in deposit were investigated.
采用自制的析磷助剂EA P作为Zn Fe P合金镀层中的磷源 ,研究了Zn Fe P合金镀液组成及 工艺条件对镀层中磷、铁含量的影响。
Study on the Process Condition for Flowing of High-Vicosity Ceramic Slurry
TiO2 film is prepared by the method of cathodic electrodeposition in peroxotitanium solution of pure TiCl4,and the mechanism and process condition of electrochemical deposition are studied.
Optimal Process Condition of Reaction-Separation Recycle System
Process Condition Optimization of Methanol Steam Reforming for Hydrogen Production
Optimization of Hydrogen Gas-Adsorption Drying Process Condition on Molecular Sieves
我想查看译文中含有： 查询“工艺条件”译词为用户自定义的双语例句 的双语例句
In the etching of SiO2 in a СHF3 + H2 plasma under certain process conditions, groove ridges were formed at the bottom of the etched groove.
Process conditions ensuring living polymerization have been found.
The influence of the electrolyte composition and process conditions on electrolytic deposition of the zinc-cobalt alloy was studied.
The catalyst efficiency in desulfurization, deasphalting, and demineralization of black oil is estimated as dependent on the catalyst pore structure and process conditions.
Major pathways of p-diethylbenzene transformations were determined depending on the process conditions.
It was found that the character of conductivity decay in a photoreceptor after positive or negative corona charging of its outer surface depended on the technological conditions of substrate pretreatment.
Using this method makes it possible to substantiate the choice of the optimal design of contact units in cascade pneumatic classifiers for various technological conditions.
Phase composition of Ti-C Films obtained under the technological conditions of diamond formation at a carbon content of above 50
Thin (6-12 nm) epitaxial MnAs films were MBE-grown on Si(111) substrates under different technological conditions.
The electrophysical and photoelectric properties of the films depend on the technological conditions of growth and are determined by states at intergrain boundaries.
It is shown that a nanoseconds microwatts bistable operation of a centimeter device is realizable under nowaday technological condition.
The technological process of the method may use either one or two-step process, and the technological condition are uncomplicated and easy to master.
Attaining ultrahigh draw ratios is a common technological condition.
In principle, this severe technological condition does not have a direct impact on the waste production, but it undoubtedly has an indirect impact.
In order to keep well-determined process condition in the knitting manufacturing, it is strongly suggested that all knitting elements and parameters should be in the integrated control circumstance.
In the second stage of the work, the process was scaled up with design and operational considerations, namely, packing medium, process condition, and configuration selections.
For each process condition, samples of both streams (distillate and residue) were collected and stored at -18°C before tocopherols analyses.
Process condition employed in the decortication of cowpeas and production of cowpea flour influence the quality of subsequent products made from the flour.
The status of grooving was evaluated through analysis of the acoustic emission (AE) signal resulted in each process condition.